Effects of structural parameters on volume flux and correction factor of jet of nozzles used lubricating gears

Authors

ZHOU Fang, Central South University, School of Mechanical and Electrical Engineering, Changsha, Hunan 410083, China; Central South University, State Key Laboratory for High Performance Complex Manufacturing, Changsha, Hunan 410083, China
LIU Shaojun, Central South University, School of Mechanical and Electrical Engineering, Changsha, Hunan 410083, China; Central South University, State Key Laboratory for High Performance Complex Manufacturing, Changsha, Hunan 410083, China
ZHANG Ruiqiang, Central South University, School of Mechanical and Electrical Engineering, Changsha, Hunan 410083, China; Central South University, State Key Laboratory for High Performance Complex Manufacturing, Changsha, Hunan 410083, China
LIN Ling, The 722 Research Institute of CSIC, Wuhan, Hubei 430079, China

Abstract

In order to study the effects of structural parameters on volume flux and correction factor of jet of nozzles used lubricating gears, single phase flow model of the jet flow field of three dimensional nozzles is simulated by employing the Large Eddy Simulation based on the FLUENT. The rationality of the simulation results of the single phase flow model of jet flow field of three dimensional nozzles were demonstrated by the volume flux of jet oil measured by the method of weighting jet oil. The results indicate that the volume flux of jet is influenced by the orifice diameter, the axial length of orifice and the angle between the axis of nozzle orifice and the axis of upstream flow channel influencing the water head loss. The correction coefficient of quantity of flow increases as the orifice diameter, the angle between orifice axis and upstream axis increase and as the orifice axial length decreases.

Publication Date

3-28-2016

First Page

104

Last Page

108

DOI

10.13652/j.issn.1003-5788.2016.03.022

Recommended Citation

Fang, ZHOU; Shaojun, LIU; Ruiqiang, ZHANG; and Ling, LIN (2016) "Effects of structural parameters on volume flux and correction factor of jet of nozzles used lubricating gears," Food and Machinery: Vol. 32: Iss. 3, Article 22.
DOI: 10.13652/j.issn.1003-5788.2016.03.022
Available at: https://www.ifoodmm.cn/journal/vol32/iss3/22

References

[1] 贾月梅. 流体力学[M]. 北京: 国防工业出版社, 2006: 51-226.
[2] 刘沛清. 自由紊动射流理论[M]. 北京: 北京航空航天大学出版社, 2008: 14-98.
[3] Cai Jin-sheng, Tsai Her Mann, Liu Feng. Numerical simulation of vortical flows in the near field of jets from notched circular nozzles[J]. Computers & Fluids, 2010, 39(3): 539-552.
[4] Sun Zuo-yu, Li Guo-xiu, Chen Chuan, et al. Numerical investigation on effects of nozzle’s geometric parameters on the flow and the aviation characteristics within injector’s nozzle for a high-pressure common-rail DI diesel engine[J]. Energy Conversion and Management, 2015, 89(1): 843-861.
[5] Xiao F, Dianat M, McGuirk J J. LES of turbulent liquid jet primary breakup in turbulent coaxial air flow[J]. International Journal of Multiphase Flow, 2014(60): 103-118.
[6] 王延忠, 牛文韬, 唐文, 等. 喷油方位参数对航空直齿轮喷油润滑过程的影响分析[J]. 航空动力学报, 2015, 30(7): 1 605-1 610.
[7] 王延忠, 牛文韬, 唐文, 等. 喷油嘴喷射方向偏离的影响因素[J]. 航空动力学报, 2012, 27(7): 1 665-1 670.
[8] 汤毅, 谢晶, 王金峰, 等. CFD预测风机摆设形式对冷库的影响[J]. 食品与机械, 2012, 28(1): 124-128.
[9] 柴宏生. 亚音速射流试验台的设计与流场模拟[D]. 武汉: 华中科技大学, 2012: 8-33.
[10] 陈海涛, 张裕中. 叶轮角度与流体黏度对高剪切罐内流体影响的模拟研究[J]. 食品与机械, 2012, 28(5): 131-134.
[11] 王延忠, 牛文韬, 唐文, 等. 航空直齿轮喷油润滑油气两相流分析[J]. 航空动力学报, 2013, 28(2): 439-444.
[12] 周建钊, 徐肖攀, 朱自成, 等. 基于ICEM CFD与ANSYS FLUENT的热力射流喷嘴流场分析[J]. 机床与液压, 2014, 42(17): 157-160, 122.
[13] Wang Fu-jun, Fang Tie-gang. Liquid jet breakup for non-circular orifices under low pressures[J]. International Journal of Multiphase Flow, 2015(72): 248-262.
[14] 张兆顺, 崔桂香, 许春晓. 湍流大涡数值模拟的理论和应用[M]. 北京: 清华大学出版社, 2008: 54-129.
[15] 唐家鹏. FLUENT14.0超级学习手册[M]. 北京: 人民邮电出版社, 2013: 39-66.